Skip to content
TRUSTED BY OVER 1 MILLION AUSSIES | FREE SHIPPING $70+
TRUSTED BY 1 MILLION+ AUSSIES | FREE SHIPPING $70+
About Us Contact Us FAQ Recycling Commercial Track BatteryMate Advantage News & Blogs DYI Guides
How to Program a Boss / Steel-Line BHT4 2211-L Compatible Garage Remote
Updated September 9, 2026

How to Program a Boss / Steel-Line BHT4 2211-L Compatible Garage Remote

Pair a compatible Boss or Steel-Line BHT4 / 2211-L remote in a few minutes: press the Learn / Code Set button on the motor, press the remote once, press Learn again and test.

Time required 10 min
Difficulty Easy
Tools needed
  • The new compatible remote with its battery fitted
  • Flat screwdriver (wall-mounted motors, to release the faceplate)
  • A small pointed object such as a pen or paperclip (ceiling motors)
  • Step ladder if the motor is on the ceiling
Before you start Make sure nobody is standing under or near the door while you program and test. Do this within a few metres of the motor so you can test straight away. Keep the remote and its battery away from children; if a coin or button cell is swallowed, seek immediate medical attention. If you need to open the motor housing, switch the power off first and only remove the cover the manual refers to. If you are not confident working near the motor, ask a garage door technician.

Boss and Steel-Line openers learn a new remote through a Learn / Code Set button. The button is behind the grey faceplate on wall-mounted units and inside a small hole on the back of ceiling-mounted motors.

Applies to

Compatible replacement remotes for Boss and Steel-Line BHT4, HT4 and 2211-L handsets, including Boss Guardian openers that use BOL4, BOL6 and BRD1 remotes.

Before you start

Work out whether your motor is wall or ceiling mounted, since the way you reach the learn button differs. Have the remote in your hand before you press the learn button.

Independent programming guide for compatible replacement remotes. Brand and model names belong to their respective owners.

Step-by-step instructions

  1. Get to the learn button

    Wall-mounted motor: slide a flat screwdriver into the small slot at the bottom centre of the grey faceplate and lift it off. Ceiling motor: find the small Radio Set / Code Set / Learn hole, usually on the rear of the motor.

  2. Press the learn button once

    Wall unit: press the small black Learn / Code Set button once. Ceiling motor: push a pointed object into the learn hole and press once. A light comes on to show the motor is ready for a remote.

  3. Press the new remote once

    Press and release the button on the new remote that you want to operate the door. The learning light blinks to confirm the code has been stored.

  4. Press the learn button again

    Press and release the Learn / Code Set button once more to leave learn mode.

  5. Test and close up

    Press the remote to check the door operates, then refit the faceplate on a wall-mounted unit.

Related Products

Garage Door Remote Control Compatible with Boss Steel Line BHT4 2211-L (TX) HT4 - Battery Mate
Garage Door Remote Control Compatible with Boss Steel Line BHT4 2211-L (TX) HT4 2211L
$17.95
2x Boss Guardian SteelLine 2211L Garage Door Remote BHT4/BOL4/BOL6/BRD1 Replacement - Battery Mate
[2 Pack] Boss Guardian Steel-Line SteelLine 2211L Garage Door Remote BHT4/BOL4/BOL6/BRD1 Replacement
$28.95

Frequently asked questions

I do not have my original remote. Can I still program this one?
Yes. This remote pairs directly with the Boss or Steel-Line motor or receiver using the learn button, so an original remote is not required.
Is my motor wall mounted or ceiling mounted?
Wall-mounted Boss units are a grey control box on the wall beside the door with a removable faceplate. Ceiling units sit on the ceiling behind the door with a learn hole on the back.
The learning light never blinked.
Press the remote button once, firmly, within a few seconds of pressing the learn button. If it still does not blink, replace the remote battery and repeat from step 2.
Which Boss and Steel-Line models does this cover?
Compatible remotes for the BHT4, HT4 and 2211-L handsets, and Boss Guardian units using the BOL4, BOL6 and BRD1 remotes.
Does the remote come with a battery?
Yes, a battery is pre-installed. If the LED on the remote does not light when you press a button, replace the battery before troubleshooting the programming.
Filed in: boss, garage-remote, how-to, remote programming, steel-line

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare